Fermer I. aldweb

Fermer II. Gratuitiels PC

Fermer III. Gratuitiels Palm

Fermer IV. Partagiciels Palm

Fermer V. iziBasic Palm

Fermer VI. Connaissance Palm

Fermer VII. Ordinateur Poche

Fermer VIII. miniPortail

Spécial !

Version mobile
de l'aldweb Site

Ni Français, ni Anglais ?

Essayez donc l'un de ces drapeaux :
[de] [es] [it] [pt]

Météo / Spam / www

Météo Lyon

aldweb contre le SPAM

Pour avoir des nouvelles de ce site, inscrivez-vous à notre Newsletter.
Se désabonner
298 Abonnés
Sites web de la famille

Webmaster - Infos
News Amis


   visiteurs en ligne

Comment trouve-tu le nouvel habillage de l'aldweb Site ?
Superbe !
forum.gifForum - iziBasic - Sujet n°1605

Forum - Forum
iziBasic - iziBasic

Warning: A non-numeric value encountered in /web5/aldweb/www/aldweb_com/www/thread.php on line 257

actif  Sujet n° 1605  Source code

le 30/12/2007 @ 14:07
par Gary


I am new to izibasic and I am also a beginner programer as well. The last time I use a basic programming language was when apple II's where new.

I have written a few small programs in Quartus Forth that I use for my work as a carpenter.

My first question is how do I generate the entire source code into the memo pad. I gotten it to generate the source code from the beginner program that's used in the manual, but I dosen't generate the entire code, just the begin and end stuff none of the objects like check boxes and buttons.
I want to be able to see the source code from other progams so I can refresh my memory of the basic language. I've generated the code for ViziBinDec, but just like the beginner program none of the gosubs and calculations showed up, only the begin and end.

By the way I use ViziBasic not the memo pad to write code. I haven't been able to generate code in ViziBasic, I tried, but nothing happens. It's says source code was generated, but I haven't found it yet. Thats why I have it generate to the memo pad.

  Poster une réponse  Haut

Warning: A non-numeric value encountered in /web5/aldweb/www/aldweb_com/www/thread.php on line 497
Réponse n° 1
le 30/12/2007 @ 23:12
par aldweb


Hello Gary,

Welcome back to Basic programming.
Your history is very similar to mine, I started coding in Basic on Sharp Pocket Computers back in the 1980's, then some BASICA in DOS... then iziBasic!

I am a little bit confused by your message, but I think that the misunderstanding is in the type of file source code is saved by ViziBasic: this is the so called DOC format and you will need a doc editor to read them and modify them. Consider the Notepad as a "cheap" starting alternative.
Please read explanations about DOC editors in the appendix #3 of the iziBasic user manual. With any DOC editor, you will get to see source codes generated by ViziBasic.

Ecrire à aldweb   Poster une réponse  Haut

Warning: A non-numeric value encountered in /web5/aldweb/www/aldweb_com/www/thread.php on line 497
Réponse n° 2
le 31/12/2007 @ 12:52
par Gary


Thanks, I will do that.

  Poster une réponse  Haut

Warning: A non-numeric value encountered in /web5/aldweb/www/aldweb_com/www/thread.php on line 497
Réponse n° 3
le 02/01/2008 @ 19:05
par Nate Weil


welcome to the izibasic community Gary!
First, memo pad doesn't recognize recognize regular doc formats, that's why your program isn't showing up. Second, for a great doc editor that works in sync with izibasic too, I highly recommend srcedit. What I do is make my basic program with visibasic, create source code, open and work on it in srcedit, then I compile it.
Ecrire à Nate Weil   Poster une réponse  Haut
actif sujet actif   clos sujet clos   Important! Important!   Nouveau Nouveau message   -   Rectifier Rectifier message   Clôturer Clôturer sujet   Remonter Remonter
Catégories de discussion  Forum 

^ Haut ^