aldweb

Close I. aldweb

Close II. PC Freeware

Close III. Palm Freeware

Close IV. Palm Shareware

Close V. iziBasic Palm

Close VI. Palm Knowledge

Close VII. Pocket Computer

Close VIII. miniPortail

Special !



Mobile version of
the aldweb Site

m.aldweb.com


Neither French, nor English?

Try one of these flags then:
[de] [es] [it] [pt]
Search




Weather / Spam / www

Lyon Weather


aldweb against spam


Newsletter
To receive news about this website, consider subscribing to our Newsletter.
Subscribe
Unsubscribe
298 Subscribers
Family's web sites

Webmaster - Infos
Friends News
Visits

   visitors

   visitors online

Poll
What do you think of the new design of the aldweb Site?
 
Great !
Beautiful
Average
So ugly...
Results
forum.gifForum - iziBasic - Topic #1629

Forum - Forum
iziBasic - iziBasic


Warning: A non-numeric value encountered in /web5/aldweb/www/aldweb_com/www/thread.php on line 257

active  Topic # 1629  Something weird is happening.

13/03/2009 @ 09:55
by Gary

Anonymous



I am in the middle of a program that solves triangles. So far every thing is working properly except for one little issue that is driving me crazy. First, there is a lot of calculations being done and they are working properly. I have it set up so the result is printed on a triangle I drew on the screen. The triangle on the screen is static, but the results have to move around a little to fit. For example, the results are printed on the screen in fraction form not decimal. Sometimes the result is in the form 3 ˝ and sometimes it's just 3, so I need to move the printed number just a little to keep it in position.

The problem I am having is when the number is a fraction like 3 ˝ it prints ok, but if it comes out to just 3 it prints it fine, but when it finishes printing it moves a different number that's in a different position and moves it out of it's original position.

When the calculations are done it leaves the number in decimal form and I have a sub procedure that takes the decimal number and turns it into a fraction like 3.5 decimal would turn into 3, 1, 2 and those numbers gets printed to the screen like this 3 ˝ .

I am using sub procedures with all the printing, for example:
GOSUB print_rise
GOSUB print_run
GOSUB print_hyp
When I enter 3 into RISE and 4 into the RUN then it prints 5 into HYP, but when the RUN turns out to be a single number like 4 it react kind of weird. It prints the 5 into the HYP properly, but moves the 4 that is already printed in RUN to a different position. How can that happen when I didn't call the print_run sub procedure? I calculated the HYP from the RISE and RUN and then I call GOSUB print_hyp.

It's been driving my nuts the only thing different in the way it prints a fraction like 3 ˝ and 3 is it moves the 3 forward a little. It seems to pass all the variables properly and calculates perfectly.

Anybody else have anything like this happen?

I do have a lot of A=this and B=that and C=A+B and I do use the A's, B's and C's multiple times, but they are always redefined in each sub procedure.

Gary



Write to Gary   Post an answer  Top

Warning: A non-numeric value encountered in /web5/aldweb/www/aldweb_com/www/thread.php on line 497
Answer n° 1
--------
15/03/2009 @ 10:17
by Gary

Anonymous

visitor
Never mind, I found the problem.
Write to Gary   Post an answer  Top

Warning: A non-numeric value encountered in /web5/aldweb/www/aldweb_com/www/thread.php on line 497
Answer n° 2
--------
15/03/2009 @ 13:27
by aldweb

Anonymous

visitor
Good news Gary

Cheers,
aldweb
Write to aldweb   Post an answer  Top
active topic active   closed topic closed   Sticky Sticky   New New message   -   Correct Correct message   Close Close topic   Make sticky Make sticky
[]
Forum Topic  Forum 



 
^ Top ^